敬业的IT人 >> 网络技术 >> 网络协议 >> 在NBMA网络广播模式下配置OSPF实际案例（配图）＋详细验证过程

在NBMA网络广播模式下配置OSPF实际案例（配图）＋详细验证过程

敬业的IT人互联网佚名 2008-3-20 10:28:53

广播式网络是一个渐进的操作过程,它可以定义所有邻居。当给一个接口配置广播时，这个接口就好像是连入了LAN中，网络中仍要选出DR和BDR，需特别保证路由器选出的DR/BDR与网络中所有路由器都有物理连接。

使用接口命令ip ospf network broadcast可以向所有路由器上设置网络类型。R2、R4的串行接口被配置成OSPF PRIORITY为0，这将保证R3成为DR。

// 帧交换机

frame-relay switching

int s2/0

encapsulation frame-relay

clock rate 64000

frame-relay intf-type dce

frame-relay route 200 int s3/0 300

int s3/0

encapsulation frame-relay

clock rate 64000

frame-relay intf-type dce

frame-relay route 300 int s2/0 200

frame-relay route 399 int s4/0 400

int s4/0

encapsulation frame-relay

clock rate 64000

frame-relay intf-type dce

frame-relay route 400 int s2/0 399

// R2 //

int lo0

ip ad 2.2.2.2 255.255.255.0

int s2/0

encapsulation frame-relay

ip ospf network broadcast //将OSPF网络类型设置为广播模式

ip ospf priority 0 //优先级为0，不参与DR选举

ip ad 192.1.1.2 255.255.255.0

frame-relay map ip 192.1.1.3 200 broadcast

frame-relay map ip 192.1.1.4 200 broadcast

router os 1

network 2.2.2.2 0.0.0.0 area 0

network 192.1.1.2 0.0.0.0 area 0

// R3 //

int lo0

ip ad 3.3.3.3 255.255.255.0

int s3/0

encapsulation frame-relay

ip ospf network broadcast //将OSPF网络类型设置为广播模式

ip address 192.1.1.3 255.255.255.0

frame-relay map ip 192.1.1.2 300 broadcast

frame-relay map ip 192.1.1.4 399 broadcast

router os 1

network 3.3.3.3 0.0.0.0 area 0

network 192.1.1.3 0.0.0.0 area 0

// R4 //

int lo0

ip ad 4.4.4.4 255.255.255.0

int s4/0

encapsulation frame-relay

ip ad 192.1.1.4 255.255.255.0

ip ospf network broadcast //将OSPF网络类型设置为广播模式

ip ospf priority 0 //优先级为0，不参与DR选举

frame-relay map ip 192.1.1.2 400 broadcast

frame-relay map ip 192.1.1.3 400 broadcast

router os 1

network 4.4.4.4 0.0.0.0 area 0

network 192.1.1.4 0.0.0.0 area 0

[下载]网吧培训与解决方案.pdf
[下载]华为AR18路由器配置实例.pdf
[下载]Cisco 官方配置范例 PDF 合集
[下载]CISCO路由器配置手册
[下载]CCNA-CCNP考试命令总结.rar
[下载]华为ADSL Modem MT800内置路由功能设
华为认证工程师HCNE培训资料

Cisco交换机、路由器密码恢复方法（精
[下载]MSR典型配置实例V1.0
[下载]华为MA5200F手册
[下载]华为MA5200典型配置
[华为技术]华为8850配置文档
华为认证网络工程师题库（中文版）
[网络工程]中国电信CN2网络工程培训

验证过程：

一、首先来检查DR选举是否按我们的设计，R3被选举为DR，R2、R4不参与选举，同时注意网络类型是否为NBMA，hello时间间隔是否为30秒。。。。。。

r3#sh ip os int s3/0
Serial3/0 is up, line protocol is up
Internet Address 192.1.1.3/24, Area 0
Process ID 1, Router ID 3.3.3.3, Network Type BROADCAST, Cost: 64
Transmit Delay is 1 sec, State DR, Priority 1
Designated Router (ID) 3.3.3.3, Interface address 192.1.1.3
No backup designated router on this network
Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    Hello due in 00:00:27
Index 2/2, flood queue length 0
Next 0x0(0)/0x0(0)
Last flood scan length is 2, maximum is 2
Last flood scan time is 0 msec, maximum is 0 msec
Neighbor Count is 2, Adjacent neighbor count is 2
    Adjacent with neighbor 4.4.4.4
    Adjacent with neighbor 2.2.2.2
Suppress hello for 0 neighbor(s)

r2#sh ip os int s2/0
Serial2/0 is up, line protocol is up
Internet Address 192.1.1.2/24, Area 0
Process ID 1, Router ID 2.2.2.2, Network Type BROADCAST, Cost: 64
Transmit Delay is 1 sec, State DROTHER, Priority 0
Designated Router (ID) 3.3.3.3, Interface address 192.1.1.3
No backup designated router on this network
Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
Hello due in 00:00:06
Index 2/2, flood queue length 0
Next 0x0(0)/0x0(0)
Last flood scan length is 1, maximum is 1
Last flood scan time is 0 msec, maximum is 0 msec
Neighbor Count is 1, Adjacent neighbor count is 1
Adjacent with neighbor 3.3.3.3 (Designated Router)
Suppress hello for 0 neighbor(s)

r4#sh ip ospf int s4/0
Serial4/0 is up, line protocol is up
Internet Address 192.1.1.4/24, Area 0
Process ID 1, Router ID 4.4.4.4, Network Type BROADCAST, Cost: 64
Transmit Delay is 1 sec, State DROTHER, Priority 0
Designated Router (ID) 3.3.3.3, Interface address 192.1.1.3
No backup designated router on this network
Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
Hello due in 00:00:05
Index 2/2, flood queue length 0
Next 0x0(0)/0x0(0)
Last flood scan length is 1, maximum is 1
Last flood scan time is 0 msec, maximum is 0 msec
Neighbor Count is 1, Adjacent neighbor count is 1
Adjacent with neighbor 3.3.3.3 (Designated Router)
Suppress hello for 0 neighbor(s)

二、接下来观察各路由器邻居建立情况：

r2#sh ip os nei

Neighbor ID Pri State Dead Time Address Interface
3.3.3.3 1 FULL/DR 00:01:50 192.1.1.3 Serial2/0

r3#sh ip os nei

Neighbor ID     Pri   State           Dead Time   Address         Interface
4.4.4.4           0   FULL/DROTHER    00:01:41    192.1.1.4       Serial3/0
2.2.2.2           0   FULL/DROTHER    00:01:30    192.1.1.2       Serial3/0

r3#sh ip os nei

Neighbor ID Pri State Dead Time Address Interface
3.3.3.3 1 FULL/DR 00:01:48 192.1.1.3 Serial4/0

三、最后验证路由：

r2#sh ip ro

     2.0.0.0/24 is subnetted, 1 subnets
C       2.2.2.0 is directly connected, Loopback0
     3.0.0.0/32 is subnetted, 1 subnets
O       3.3.3.3 [110/65] via 192.1.1.3, 00:00:17, Serial2/0
     4.0.0.0/32 is subnetted, 1 subnets
O       4.4.4.4 [110/65] via 192.1.1.4, 00:00:17, Serial2/0
C    192.1.1.0/24 is directly connected, Serial2/0

r3#sh ip ro

     2.0.0.0/32 is subnetted, 1 subnets
O       2.2.2.2 [110/65] via 192.1.1.2, 00:00:38, Serial3/0
     3.0.0.0/24 is subnetted, 1 subnets
C       3.3.3.0 is directly connected, Loopback0
     4.0.0.0/32 is subnetted, 1 subnets
O       4.4.4.4 [110/65] via 192.1.1.4, 00:00:38, Serial3/0
C    192.1.1.0/24 is directly connected, Serial3/0

r4#sh ip ro

     2.0.0.0/32 is subnetted, 1 subnets
O       2.2.2.2 [110/65] via 192.1.1.2, 00:01:04, Serial4/0
     3.0.0.0/32 is subnetted, 1 subnets
O       3.3.3.3 [110/65] via 192.1.1.3, 00:01:04, Serial4/0
     4.0.0.0/24 is subnetted, 1 subnets
C       4.4.4.0 is directly connected, Loopback0
C    192.1.1.0/24 is directly connected, Serial4/0
r4#

如果我们将R2路由器的优先级调整为10，重启后R2将成为DR，R3作为BDR，R4作为DROTHER，这样的结果会导致R4无法收到R2、R3的路由更新，原因如下：

r4#sh ip ospf database

OSPF Router with ID (4.4.4.4) (Process ID 1)

Router Link States (Area 0)

Link ID         ADV Router      Age         Seq#       Checksum Link count
2.2.2.2         2.2.2.2         99          0x80000009 0xCF69   2
3.3.3.3         3.3.3.3         109         0x8000000B 0xDF4A   2
4.4.4.4         4.4.4.4         107         0x8000000C 0xFB1F   2

Net Link States (Area 0)

Link ID ADV Router Age Seq# Checksum
192.1.1.2 2.2.2.2 108 0x80000001 0x4910

r4#sh ip os database router

OSPF Router with ID (4.4.4.4) (Process ID 1)

Router Link States (Area 0)

Adv Router is not-reachable
LS age: 124
Options: (No TOS-capability, DC)
LS Type: Router Links
Link State ID: 2.2.2.2
Advertising Router: 2.2.2.2
LS Seq Number: 80000009
Checksum: 0xCF69
Length: 48
Number of Links: 2

    Link connected to: a Transit Network
     (Link ID) Designated Router address: 192.1.1.2
     (Link Data) Router Interface address: 192.1.1.2
      Number of TOS metrics: 0
       TOS 0 Metrics: 64

    Link connected to: a Stub Network
     (Link ID) Network/subnet number: 2.2.2.2
     (Link Data) Network Mask: 255.255.255.255
      Number of TOS metrics: 0
       TOS 0 Metrics: 1

Adv Router is not-reachable
LS age: 198
Options: (No TOS-capability, DC)
LS Type: Router Links
Link State ID: 3.3.3.3
Advertising Router: 3.3.3.3
LS Seq Number: 8000000B
Checksum: 0xDF4A
Length: 48
Number of Links: 2

    Link connected to: a Transit Network
     (Link ID) Designated Router address: 192.1.1.2
     (Link Data) Router Interface address: 192.1.1.3
      Number of TOS metrics: 0
       TOS 0 Metrics: 64

    Link connected to: a Stub Network
     (Link ID) Network/subnet number: 3.3.3.3
     (Link Data) Network Mask: 255.255.255.255
      Number of TOS metrics: 0
       TOS 0 Metrics: 1

LS age: 215
Options: (No TOS-capability, DC)
LS Type: Router Links
Link State ID: 4.4.4.4
Advertising Router: 4.4.4.4
LS Seq Number: 8000000C
Checksum: 0xFB1F
Length: 48
Number of Links: 2

    Link connected to: a Transit Network
     (Link ID) Designated Router address: 192.1.1.3
     (Link Data) Router Interface address: 192.1.1.4
      Number of TOS metrics: 0
       TOS 0 Metrics: 64

    Link connected to: a Stub Network
     (Link ID) Network/subnet number: 4.4.4.4
     (Link Data) Network Mask: 255.255.255.255
      Number of TOS metrics: 0
       TOS 0 Metrics: 1

最新文章: OSPF虚链路（virtual-link）配置实例 + 详细..[03-20]; OSPF邻居认证实际案例（配图）＋详细验证过程[03-20]; 和剑桥合作：新协议为BT更大地提速[03-20]; SMTP协议简介（Simple Mail Transfer ..[03-20]; SMTP协议简介 (Simple Mail Transfer..[03-20]; 解决设备内容共享 UPnP协议成为ISO标准[03-20]

相关文章: OSPF虚链路（virtual-link）配置实例 + 详细..[03-20]; OSPF邻居认证实际案例（配图）＋详细验证过程[03-20]; 教你配置OSPF动态路由协议的身份验证[03-20]; RFC1204 - Message Posting Prot..[03-20]; 常见网络协议介绍[03-20]; TiVo与Brightcove达成协议欲推网络视频服务[03-20]